Products Category
WD-KEV2/220
Product Description
Large flow capacity, multi-level protection.
Built in fast semiconductor protection device, fast response and low residual voltage.
The core components are international famous brands with superior performance.
Energy saving, environmental protection, simple installation, applicable to various standard interface types.
Low insertion loss to ensure smooth line.
The standing wave coefficient is small, and the operating frequency range is wide.
Product parameter description of guide rail lightning arrester
|
Name |
Type |
Rated operating voltage（Un） |
Maximum continuous operating voltage（Uc） |
Rated load current（IL） |
Nominal discharge current（In）（8/20μs） |
Maximum discharge current（Imax）（8/20μs） |
Voltage protection level（Up） |
Transmission speed（Vs） |
Insertion loss（Ae） |
||||||||
|
Guide rail type 100 megabyte network lightning protector |
TL-E100 |
5V |
8V |
1A |
5Ka |
10Ka |
≤15V |
100M |
≤0.3dB |
||||||||
|
Guide rail type gigabit network lightning protector |
TL-E1000 |
5V |
8V |
1A |
5Ka |
10Ka |
≤15V |
100M |
≤0.1dB |
||||||||
|
Network part/power supply part |
Network/Power |
Network/Power |
Network/Power |
Network/Power |
Network/Power |
Network/Power |
Network/Power |
Network/Power |
|||||||||
|
Guide rail 100M POE network lightning protector |
TL-POE/E100 |
5V |
48V |
8V |
100V |
1A |
1A |
5Ka |
5Ka |
10Ka |
10Ka |
≤15V |
≤100V |
100M |
- |
≤0.3dB |
- |
|
Guide rail type gigabit POE network lightning protector |
TL-POE/E1000 |
5V |
48V |
8V |
100V |
1A |
1A |
5Ka |
5Ka |
10Ka |
10Ka |
≤15V |
≤100V |
100M |
- |
≤0.3dB |
- |
|
12V network two in one lightning protector (100M) |
TL-EP/12 |
5V |
12V |
8V |
18V |
1A |
2A |
5Ka |
5Ka |
10Ka |
10Ka |
≤15V |
≤60V |
100M |
- |
≤0.3dB |
- |
|
24V network two in one lightning arrester (100M) |
TL-EP/24 |
5V |
24V |
8V |
47V |
1A |
2A |
5Ka |
5Ka |
10Ka |
10Ka |
≤15V |
≤90V |
100M |
- |
≤0.3dB |
- |
|
220V network two in one lightning arrester (100M) |
TL-EP/220 |
5V |
220V |
8V |
470V |
1A |
2A |
5Ka |
5Ka |
10Ka |
10Ka |
≤15V |
900V |
100M |
- |
≤0.3dB |
- |
|
12V network two in one lightning protector (1000M) |
TL-KEV2/12 |
5V |
12V |
8V |
18V |
1A |
2A |
5Ka |
5Ka |
10Ka |
10Ka |
≤15V |
≤60V |
100M |
- |
≤0.3dB |
- |
|
24V network two in one lightning arrester (1000M) |
TL-KEV2/24 |
5V |
24V |
8V |
47V |
1A |
2A |
5Ka |
5Ka |
10Ka |
10Ka |
≤15V |
≤90V |
100M |
- |
≤0.3dB |
- |
|
220V network two in one lightning arrester (1000M) |
TL-KEV2/220 |
5V |
220V |
8V |
470V |
1A |
2A |
5Ka |
5Ka |
10Ka |
10Ka |
≤15V |
≤900V |
100M |
- |
≤0.3dB |
- |
Dimension specification of guide rail lightning arrester
Installation diagram of guide rail lightning arrester
Installation Instructions
This product is connected in series.
Please select a product with the same interface type as the protected device.
A-A/B-B of this product; (L/+) - (L/+)/(N/-) - (N/-) channels are one-to-one corresponding, and cross wiring is prohibited.
The "IN" of the lightning arrester is the input terminal connected to the "surge terminal" line, and the "OUT" is the output "equipment terminal" connected to the protected equipment.
The PE line of the lightning arrester must be reliably connected with the ground wire of the lightning protection system, and the connecting line is required to be short and thick.
The lightning arrester shall be tested regularly during its use. In case of failure, it shall be repaired or replaced in time to ensure the safety of the equipment